Knowledge base · regulation · OTSZ · 3/2002 SzCsM–EüM

Duct cleaning: when is it mandatory, and what must you be able to prove?

Duct cleaning is one of those tasks everyone knows is “required”, but few can say exactly on what basis and how often. The question actually runs along two independent regulatory threads, and they expect different things.

This article summarises the framework. The precise duty for your facility is always determined by the consolidated legal text, the equipment manufacturer’s specification and — in disputed cases — the position of your fire-safety expert.

Two threads: fire safety and occupational safety

1. Fire safety — the grease extract

This is the stricter and more concrete one. The Hungarian National Fire Safety Code (OTSZ, Decree 54/2014. (XII. 5.) BM) prescribes periodic cleaning for ventilation equipment where combustible material may deposit — typically the grease extract systems of hot kitchens, restaurants and canteens.

The logic is:

  • cleaning must follow the frequency specified by the manufacturer;
  • absent a manufacturer’s specification, the interval set in the decree applies;
  • completion must be documented in writing.

The specific intervals differ by building type and use, and can change with amendments. Technical guidelines (TvMI) also attach to the details, and they are not the same instrument as the decree. So always confirm your own interval from the consolidated text (njt.hu) or with a fire-safety expert — the “every six months / annually” rules of thumb circulating online often mix up their sources.

Why this is not a formality: a grease-coated duct is combustible material inside a pipe network that is ideally suited to spreading fire and runs through the whole building. A kitchen fire can travel through a contaminated duct in minutes into rooms with no ignition source at all. Neglecting cleaning can result in fire-safety fines — and in case of damage, the insurer will also examine whether documented cleaning took place.

2. Occupational safety — ventilation in general

The second thread is quieter but broader. Section 6 (4) of joint Decree 3/2002. (II. 8.) SzCsM–EüM on the minimum occupational-safety requirements for workplaces requires ventilation systems to be kept regularly clean, with accumulated deposits removed without delay.

There is no calendar interval here — “regular” means whatever the system’s fouling rate justifies. The employer’s general responsibility for healthy and safe working conditions is set by the Occupational Safety Act (Act XCIII of 1993); 3/2002 is its concrete workplace implementation.

This thread therefore covers the production hall’s ventilation, the office AHU and process extraction — not just the kitchen.

What does an inspection look at?

Not the inside of the duct — the paperwork. In practice, these are requested:

  • a cleaning report: when, what scope, what method,
  • photo documentation of the before and after condition,
  • documentation of the next due date,
  • the system’s maintenance log, into which these are entered.

Which leads to a practical tip: when ordering the cleaning, order the documentation too. A perfectly executed cleaning without a report does not exist as far as an inspection is concerned.

How do you know it’s due?

Beyond the calendar, the system signals for itself:

  • Odour in the supply air — typically organic deposits or moisture.
  • Dusty supply grilles, deposits on the louvres: what you can see is a fraction of what is in the duct.
  • Falling air delivery: the room “doesn’t ventilate”, steam lingers in the kitchen.
  • Rising fan consumption at the same setting.
  • Recurring complaints: headaches, eye irritation, “bad air” — classic signs of degrading indoor air quality.
  • In kitchens: grease dripping at the grille or duct joints. This is a late sign.

What happens during cleaning?

A reliable process looks roughly like this:

  1. Survey: mapping the network, taking stock of access points (cleaning hatches), assessing contamination.
  2. Cleaning hatches created where there are none. In older systems this is often the neglected part: without access, there is no verifiable cleaning.
  3. Mechanical cleaning: rotary brush method combined with industrial extraction, so the dislodged contamination does not end up in the room.
  4. Degreasing (kitchen systems): chemical dissolution, then rinsing.
  5. Filter replacement where the system calls for it.
  6. Documented handover: report, photos, recommendation for the next interval.

The work can usually be done outside operating hours — at night, on weekends — or in stages, so production and hospitality do not stop.

In summary

Cleaning a grease-laden kitchen extract is a fire-safety duty, at the manufacturer’s or the decree’s frequency, with written documentation. Keeping workplace ventilation systems clean is an occupational-safety requirement with no fixed calendar interval, matched to the rate of fouling. In both cases, what counts is what you can evidence.

If you don’t know when your system was last cleaned — that is an answer in itself. Request a survey: we inspect the network and tell you what is due and on what schedule.

Request a quote

Describe the job — we assess it.

Site, equipment, deadline — that is enough to start. We respond on short notice.

Request a quote
Immersive preview ▸